1350 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M194

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M194 1350 Lab2u

INDEXABLE MILLING INDEXABLE MILLING RECOMMENDED CUTTING CONDITIONS Note 1) The cutting conditions below are a guide only. Please make adjustments according to the machining conditions. Note 2) Please note the follows when machining the hardened steel by using MP8010. Please shorten the overhang length as much as possible. Please note the setting of the depth of cut especially to prevent the fracture. Use with carbide shank recommended. The first recommended grade when machining hardened steel of less than 50HRC is VP15TF. SHOULDER MILLING POCKET MILLING RAMPING COPYING Work Material Hardness Grade Cutting Speed vc (m/min) ARX25ROOOSAOOS ARX25ROCXJMOOAOO ARX30R SA S ARX30ROOOMOOAOO ARX35R. . . SA ,..S Depth of Cut ap (mm) Feed per Tooth fz(mm/t.) Depth of Cut ap (mm) Feed per Tooth fz (mm/t.) Depth of Cut ap (mm) Feed perTooth fz(mm/t.) P Mild Steel 5180HB VP15TF 180 (150-220) 1.0 0.5 1.2 0.5 1.5 0.5 Carbon Steel Alloy Steel 180 350HB VP15TF 160 (120-200) 0.7 0.3 0.9 0.3 1.2 0.3 M Stainless Steel 5270HB VP15TF 150 (120-180) 50.7 50.3 50.9 50.3 51.2 50.3 K Gray Cast Iron Tensile Strength5350MPa VP15TF 180 (150-220) 51.0 50.5 51.2 50.5 51.5 50.5 Ductile Cast Iron Tensile Strength5800MPa VP15TF 120 (80-160) 51.0 50.5 51.2 50.5 51.5 50.5 H Hardened Steel 50HRC VP15TF 80(50-120) 0.5 0.2 0.7 0.2 1.0 0.2 >50HRC MP8010 80(50-120) 0.3 0.2 0.4 0.2 0.5 0.2 Note 1) For ramping process, ref SLOT MILLING ar to cutting criteria by type. Work Material Hardness Grade Cutting Speed vc (m/min) ARX25ROOOSAOOS ARX25RCOOMOOACO ARX30ROOOSAOOS ARX30RGCCMCCACC ARX35R; : : SA s Depth of Cut ap (mm) Feed per Tooth fz(mm/t.) Depth of Cut ap (mm) Feed per Tooth fz (mm/t.) Depth of Cut ap (mm) Feed perTooth fz(mm/t.) P Mild Steel 5180HB VP15TF 180 (150-220) 1.0 0.4 1.2 0.4 1.5 0.4 Carbon Steel Alloy Steel 180 350HB VP15TF 160 (120-200) 0.7 0.2 0.9 0.2 1.2 0.2 M Stainless Steel 5270HB VP15TF 150 (120-180) 0.7 0.2 0.9 0.2 1.2 0.2 K Gray Cast Iron Tensile Strength<350MPa VP15TF 180 (150-220) 1.0 0.4 1.2 0.4 1.5 0.4 Ductile Cast Iron Tensile Strength<800MPa VP15TF 120 (80-160) 1.0 0.4 1.2 0.4 1.5 0.4 H Hardened Steel 50HRC VP15TF 80 (50-120) 0.5 0.1 0.7 0.1 1.0 0.1 >50HRC MP8010 80 (50-120) 0.3 0.1 0.4 0.1 0.5 0.1 IPLUNGING Work Material Hardness Grade Cutting Speed vc (m/min) ARX25R SA. : S ARX25R M A ARX30ROOOSAOOS ARX30RGCOMCOACO ARX35R; : : SA S Cutting Width ae (mm) Feed per Tooth fz(mm/t.) Cutting Width ae (mm) Feed per Tooth fz (mm/t.) Cutting Width ae (mm) Feed perTooth fz(mm/t.) P Mild Steel 5180HB VP15TF 180 (150-220) 2.5 0.3 3.0 0.3 3.5 0.3 Carbon Steel Alloy Steel 180 350HB VP15TF 160 (120-200) 2.5 0.2 3.0 0.2 3.5 0.2 M Stainless Steel 5270HB VP15TF 150 (120-180) 2.5 0.2 3.0 0.2 3.5 0.2 K Gray Cast Iron Tensile Strength<350MPa VP15TF 180 (150-220) 2.5 0.3 3.0 0.3 3.5 0.3 Ductile Cast Iron Tensile Strength<800MPa VP15TF 120 (80-160) 2.5 0.3 3.0 0.3 3.5 0.3 H Hardened Steel 50HRC VP15TF 80 (50-120) 2.5 0.1 3.0 0.1 3.5 0.1 >50HRC MP8010 80 (50-120) 2.5 0.1 3.0 0.1 3.5 0.1 IHELICAL DRILLING Work Material Hardness Grade Cutting Speed ARX25ROOOSAOOS ARX25RO X)MOOACO ARX30ROOOSAOOS ARX30RCCOMCOACO ARX35RCOOSAOOS vc (m/min) DOC/pass ap (rrm/pass) Feed per Tooth fz(mm/t.) DOC/pass ap (mmlpass) Feed per Tooth fz (mm/t.) DOC/pass ap (mmlpass) Feed perTooth fz(mm/t.) P Mild Steel 5180HB VP15TF 180 (150-220) 1.0 0.3 1.0 0.3 1.0 0.3 Carbon Steel Alloy Steel 180 350HB VP15TF 160 (120-200) 0.7 0.2 0.9 0.2 1.0 0.2 M Stainless Steel 5270HB VP15TF 150 (120-180) 0.7 0.2 0.9 0.2 1.0 0.2 K Gray Cast Iron Tensile Strength<350MPa VP15TF 180 (150-220) 1.0 0.3 1.0 0.3 1.0 0.3 Ductile Cast Iron Tensile Strength<800MPa VP15TF 120 (80-160) 51.0 50.3 51.0 50.3 51.0 50.3 H Hardened Steel 50HRC VP15TF 80(50-120) 50.5 50.1 50.7 50.1 51.0 50.1 >50HRC MP8010 80(50-120) 50.3 50.1 50.4 50.1 50.5 50.1 Note 1) For helical drilling, refer to the maximum capacities on page M195. M194