1346 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M190

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M190 1346 Lab2u

INDEXABLE MILLING INDEXABLE MILLING RECOMMENDED CUTTING CONDITIONS Dry cutting Work Material Hardness Grade VC (m/min) fz (mm/t.) M Austenitic Stainless Steel 200HB MC7020 220 (170-270) 0.2 (0.1-0.35) MP7130 200 (150-250) 0.2 (0.1-0.35) Austenitic Stainless Steel >200HB MC7020 190 (140-240) 0.2 (0.1-0.35) MP7130 170 (120-220) 0.2 (0.1-0.35) Two-phase Stainless Steel 280HB MC7020 180 (130-230) 0.2 (0.1-0.35) MP7130 160 (110-210) 0.2 (0.1-0.35) Ferritic and Martensitic 5200MPa MC7020 240 (190-290) 0.2 (0.1-0.35) Stainless Steel MP7130 200 (150-250) 0.2 (0.1-0.35) Ferritic and Martensitic >200HB MC7020 240 (190-290) 0.2 (0.1-0.35) Stainless Steel MP7130 200 (150-250) 0.2 (0.1-0.35) Hardened Stainless Steel 450HB MC7020 170 (120-220) 0.2 (0.1-0.35) MP7130 150 (100-200) 0.2 (0.1-0.35) Wet cutting Work Material Hardness Grade vc (m/min) fz (mm/t.) M Austenitic Stainless Steel 200HB MC7020 150(100-200) 0.2 (0.1-0.35) MP7130 130 (80-180) 0.2 (0.1-0.35) Austenitic Stainless Steel >200HB MC7020 120 (70-170) 0.2 (0.1-0.35) MP7130 100 (80-150) 0.2 (0.1-0.35) Two-phase Stainless Steel 5280HB MC7020 120 (70-170) 0.2 (0.1-0.35) MP7130 100 (80-150) 0.2 (0.1-0.35) Ferritic and Martensitic 200MPa MC7020 170(120-220) 0.2 (0.1-0.35) Stainless Steel MP7130 130 (80-180) 0.2 (0.1-0.35) Ferritic and Martensitic >200HB MC7020 170(120-220) 0.2 (0.1-0.35) Stainless Steel MP7130 130 (80-180) 0.2 (0.1-0.35) Hardened Stainless Steel 450HB MC7020 110(60-160) 0.2 (0.1-0.35) MP7130 90 (50-140) 0.2 (0.1-0.35) S Titanium Alloy - MP9130 45 (30-55) 0.1 (0.05-0.15) Heat Resistant Alloy - MP9130 35 (15-45) 0.1 (0.05-0.15) Note 1) Actual cutting conditions are estimated to avoid chatter vibration with high rigidity of a machine or workpiece. Make appropriate adjustments when chatter and/or insert chipping occurs during cutting. Use with lowered conditions when there is a big overhang and/or when pocket-cutting. Note 2) The setting level for feeding 1 blade is ap = 2.5mm with ARP5 axial cutting. With ARP6, use ap = 3mm. Use while matching the ap fluctuation and correction value F of the respective table. Ex. Feed for the recommended 1 blade when ARP5.SUS304, MP7130,ap=1: 0.2 mmrt.x1.5 (correction value F )=0.3 mm/t Note 3) For grooving, use feed at the recommended 70% level. For ramping, drilling, and plunging, use 50% level. Note 4) Internal coolant is recommended in titanium alloy and heat resistant alloy cutting. When the coolant nozzle of separately sold is used, it is more effective. M190