1053 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.K021

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. K021 1053 Lab2u

CARBIDE Shoulder milling (L/D=3) Other than the L/D = 3, use following recommended cutting conditions by multiplying the K003 page correction factor by overhang length. (mm) Work Material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Heat resistant alloys lnconel718 Dia. DC Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth of cut ap Width of Cut ae 10 75 2400 0.03 290 8 4 40 1300 0.04 210 8 1 12 75 2000 0.033 260 9.6 4.8 40 1100 0.045 200 9.6 1.2 16 75 1500 0.038 230 12.8 6.4 40 800 0.05 160 12.8 1.6 20 75 1200 0.038 180 16 8 40 640 0.05 130 16 2 25 75 950 0.038 140 20 10 40 510 0.05 100 20 2.5 Depth of cut LU CC D o CO m n 2 Q CC CC LlI CL I Slot milling (mm) Work Material Carbon steel, Alloy steel, Mild steel, Copper, Copper alloys AISI 1045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steels, Titanium alloy AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, TI-6AI-4V Dia. DC Culling Speed (m/min) Revolution (min-1) (mm/t.) Feed rate (mm/min) Depth ofcut ap Cutting Speed (m/min) Revolution (min-1) (mm/t.) Feed rate (mm/min) Depth ofcut ap Cutting Speed (m/min) Revolution (min-1) (mm/t.) Feed rate (mm/min) Depth ofcut ap 10 12 16 20 25 100 100 100 100 100 3200 2700 2000 1600 1300 0.04 0.045 0.05 0.05 0.06 510 490 400 320 310 5 6 8 10 12 80 80 80 80 80 2500 2100 1600 1300 1000 0.03 0.032 0.038 0.038 0.038 300 270 240 200 150 5 6 8 10 12 60 60 60 60 60 1900 1600 1200 950 760 0.02 0.025 0.03 0.034 0.034 150 160 140 130 100 4 4.8 6.4 8 10 Depth of cut DC: Dia. Work Material Depth of cut Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Dia. DC Cutting Speed (m/min) Revolution (min-1) Feed per Tooth (mm/t.) Feed rate (mm/min) Depth ofcut ap 10 40 1300 0.016 83 4 12 40 1100 0.02 88 4.8 16 40 800 0.024 77 6.4 20 40 640 0.027 70 8 25 40 510 0.027 55 10 a m DC: Dia. Note 1) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. Note 2) If the depth ofcut is shallow, the revolution and feed rate can be increased. Note 3) Vibration may occur if the rigidity of machine or workpiece is low.ln this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. K021