840 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J218

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J218 0840 Lab2u

SOLID END MILLS VF2SDB VF2SDBL Ball nose, Short cut length, 2 flute, Strong geometry type Ball nose, Short cut length, 2 flute, Strong geometry type, Long shank RECOMMENDED CUTTING CONDITIONS Overhang below DCx5 (DC:Dia.) Work Material Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1 -10, AISI P21 Hardened steel (45 55HRC) AISI H13 Hardened steel (55 62HRC) AISI D2 R RE (mm) ce<15” a>15” Depthofcut ap (mm) Depthofcut ae (mm) a<15" a>15” Depthofcut ap (mm) Depthofcut ae (mm) ct<15” a>15" Depthofcut ap (mm) Depthofcut ae (mm) Revolution (min'1) Feed rate (mm/min) Revolution (min'1) Feed rate (mm/min) Revolution (min'1) Feed rate (mm/min) Revolution (min'1) Feed rate (mm/min) R 0.5 40000 5200 36000 2300 0.10 0.25 40000 5200 36000 2300 0.10 0.25 40000 5000 40000 2400 0.05 0.10 R 1 40000 6000 36000 3500 0.20 0.50 40000 6000 36000 3500 0.20 0.50 36000 5000 24000 2400 0.10 0.20 R 1.5x3 29000 4600 19000 2400 0.20 0.50 25000 4000 16000 2000 0.20 0.50 17000 2400 11000 1000 0.12 0.30 R 1.5 37000 7000 24000 3000 0.30 0.75 37000 7000 24000 3000 0.30 0.75 25000 6000 16000 2200 0.12 0.30 R 2x4 24000 4300 15000 2200 0.25 0.70 19000 3400 13000 1700 0.25 0.70 12000 1900 8200 900 0.13 0.40 R 2 30000 6500 19000 2800 0.40 1.00 28000 6000 19000 2600 0.40 1.00 18000 4800 12000 2000 0.13 0.40 R 2.5 25000 6000 16000 2600 0.50 1.30 22000 5000 16000 2300 0.50 1.25 15000 4200 9500 1700 0.15 0.50 R 3 22000 6000 14000 2400 0.60 1.80 18000 4500 12000 1900 0.60 1.50 12000 3500 8000 1600 0.20 0.60 R 4 19000 5200 12000 2200 0.80 2.40 15000 3800 9500 1700 0.80 2.00 9800 3000 6500 1300 0.20 0.80 R 5 15000 4300 9500 2000 1.00 3.00 11000 3000 7000 1500 1.00 2.50 7500 2400 5000 1000 0.20 1.00 R 6 12000 3400 8000 1800 1.20 3.60 9000 2400 6000 1400 1.20 3.00 6000 1900 4000 800 0.30 1.20 R 8 9000 2600 6000 1500 1.60 4.80 7000 1900 4500 1100 1.60 4.00 4500 1500 3000 600 0.30 1.60 R10 7500 2200 4800 1200 2.00 6.00 5500 1500 3600 900 2.00 5.00 3600 1200 2500 500 0.30 2.00 £ Ld CL LU O' 0£ OQ CD z I CD 3 o a. ae Depth of cut Ld in Note 1) a is the inclination angle of the machined surface. Note 2) If the depth of cut is shallow, the revolution and feed rate can be increased, Note 3) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. Overhang DCx7 (DC:Dia.) Work Alloy steel, Tool steel, Pre-hardened steel Hardened steel (45 55HRC) Material AISI H13, AISI W1 -10, AISI P21 AISI H13 R RE (mm) Revolution (min"1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) R 1.5x3 16000 2000 0.10 0.30 13000 1500 0.10 0.30 R 2x4 13000 2000 0.15 0.50 10000 1500 0.15 0.50 R 3 10000 2000 0.20 1.00 8000 1600 0.20 0.80 R 4 8000 1800 0.30 1.50 6400 1400 0.40 1.20 R 5 6000 1600 0.40 2.00 4800 1200 0.40 1.60 R 6 5000 1300 0.45 2.40 4000 1000 0.45 2.00 R 8 3800 1000 0.60 3.00 3100 800 0.60 2.50 R10 3000 800 0.80 4.00 2500 650 0.80 3.00 Depth of cut ae Note 1) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. J218