757 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J135

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J135 0757 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS ISide milling Work Material Carbon steel, Alloy steel (180-280HB) Ductile cast iron Carbon steel, Alloy steel (280 350HB) Pre-hardened steel, Alloy tool steel Austenitic stainless steel (5200HB) Titanium alloy Hardened steel (45-55HRC) AISI 1045, AISI 4140, FCD450 AISI 4340, AISI P21, AISI P20, SKD, SKT AISI 304, AISI 306, Ti-6AI-4V AISI H13, AISI L6 Dia. DC (mm) Length of cut APMX (mm) Revolution (min-1) Feed rale (mm/min) Depthofcut ap (mm) Depthofcut ae (mm) Revolution (min-1) Feed rate (mm/min) Depthofcut ap (mm) Depthofcut ae (mm) Revolution (min-1) Feed rate (mm/min) Depthofcut ap (mm) Depthofcut ae (mm) Revolution (min-1) Feed rate (mm/min) Depthofcut ap (mm) Depthofcut ae (mm) 1 4 19000 300 3 0.03 15000 240 3 0.03 13000 210 3 0.03 13000 160 3 0.02 1.5 6 16000 320 4.5 0.05 13000 260 4.5 0.05 11000 220 4.5 0.05 8500 170 4.5 0.03 2 6.5 15000 500 5 0.1 12000 380 5 0.1 10000 320 5 0.1 7700 220 5 0.06 8 14000 470 6 0.06 11000 350 6 0.06 9500 300 6 0.06 7300 200 6 0.04 2.5 10 13000 660 7.5 0.08 11000 520 7.5 0.08 8900 390 7.5 0.08 6300 250 7.5 0.05 3 10 13000 890 7.4 0.15 10000 620 7.4 0.15 8400 470 7.4 0.15 5900 300 7.4 0.09 12 12000 820 9 0.09 9500 590 9 0.09 8000 450 9 0.09 5600 280 9 0.06 4 13 9400 940 9.9 0.2 7500 650 9.9 0.2 6300 530 9.9 0.2 4700 320 9.9 0.12 16 9000 900 12 0.12 7200 620 12 0.12 6000 500 12 0.12 4500 310 12 0.08 5 17 7500 990 12.4 0.25 6000 680 12.4 0.25 5000 560 12.4 0.25 3800 350 12.4 0.15 20 7200 950 15 0.15 5700 650 15 0.15 4800 540 15 0.15 3600 330 15 0.1 6 20 6300 1100 14.9 0.3 5000 760 14.9 0.3 4200 640 14.9 0.3 3200 350 14.9 0.18 24 6000 1000 18 0.18 4800 730 18 0.18 4000 610 18 0.18 3000 330 18 0.12 8 26 4700 1100 19.8 0.4 3800 800 19.8 0.4 3100 620 19.8 0.4 2400 360 19.8 0.24 32 4500 1000 24 0.24 3600 760 24 0.24 3000 600 24 0.24 2300 350 24 0.16 10 33 3800 1000 24.8 0.5 3000 760 24.8 0.5 2500 590 24.8 0.5 1900 330 24.8 0.3 40 3600 970 30 0.3 2900 730 30 0.3 2400 570 30 0.3 1800 310 30 0.2 12 40 3100 1000 29.7 0.6 2500 720 29.7 0.6 2100 550 29.7 0.6 1600 300 29.7 0.36 48 3000 970 36 0.36 2400 690 36 0.36 2000 520 36 0.36 1500 280 36 0.24 16 53 2400 780 27.2 0.48 1900 550 39.6 0.8 1600 420 39.6 0.8 1200 240 39.6 0.48 64 2200 710 48 0.48 1800 520 48 0.48 1500 390 48 0.48 1100 220 48 0.32 20 66 1900 620 34 0.6 1500 430 49.5 1 1300 340 49.5 1 950 190 49.5 0.6 80 1800 580 60 0.6 1400 400 60 0.6 1200 310 60 0.6 900 180 60 0.4 m /> 2 Q DC CC LlI a. LU CC CC m 3 o DC Depth of cut ap Note 1) Wet cutting mode is recommended for cutting stainless steels and titanium alloys, and air blow is recommended for carbon steels. Note 2) The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abonrmal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth ofcut, o in J135