Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Feed per tooth is for slot milling For side millin

Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Feed per tooth is for slot milling For side milling increase Fz by 20% Cutting speed m/min Cutting speed m/min j Si i ap ae ap ae min max 6 8 10 12 16 20 25 P0 15xD 03xD 1xD 01xD 80 170 0014 0014 0017 0021 0024 0027 0027 P1 15xD 03xD 1xD 01xD 70 150 0014 0014 0017 0021 0024 0027 0027 P2 15xD 03xD 1xD 01xD 70 150 0014 0014 0017 0021 0024 0027 0027 P3 15xD 03xD 1xD 01xD 61 130 0014 0014 0017 0021 0024 0027 0027 P4 15xD 03xD 1xD 01xD 56 120 0014 0014 0017 0021 0024 0027 0027 P5 15xD 03xD 1xD 01xD 56 120 001 001 0015 0017 0021 0024 0024 P6 15xD 03xD 1xD 01xD 56 120 001 001 0015 0017 0021 0024 0024 P7 15xD 03xD 1xD 01xD 52 110 001 001 0015 0017 0021 0024 0024 M1 15xD 03xD 1xD 01xD 56 120 0017 0017 0021 0024 0027 0031 0031 K1 15xD 03xD 1xD 01xD 61 130 0014 0014 0017 0021 0024 0027 0027 K2 15xD 03xD 1xD 01xD 33 70 0014 0014 0017 0021 0024 0027 0027 K3 15xD 03xD 1xD 01xD 33 70 0014 0014 0017 0021 0024 0027 0027 Cutting data for mills 015 582 Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Feed per tooth is for slot milling For side milling increase Fz by 20% Cutting speed m/min ap ae ap ae min max 8 10 12 16 20 25 P0 15xD 03xD 1xD 01xD 108 230 0024 0027 0038 0048 0069 0069 P1 15xD 03xD 1xD 01xD 94 200 0024 0027 0038 0048 0069 0069 P2 15xD 03xD 1xD 01xD 85 180 0024 0027 0038 0048 0069 0069 P3 15xD 03xD 1xD 01xD 85 180 0024 0027 0038 0048 0069 0069 P4 15xD 03xD 1xD 01xD 66 140 0024 0027 0038 0048 0069 0069 P5 15xD 03xD 1xD 01xD 80 170 0024 0027 0038 0048 0069 0069 P6 15xD 03xD 1xD 01xD 75 160 0024 0027 0038 0048 0069 0069 P7 15xD 03xD 70 0024 0027 0038 0048 0069 0069 M1 15xD 03xD 1xD 01xD 42 90 0024 0027 0038 0048 0069 0069 M2 - 1xD 01xD - 50 0035 004 0055 007 01 01 K1 15xD 03xD 1xD 01xD 75 160 0024 0027 0038 0048 0069 0069 K2 15xD 03xD 1xD 01xD 56 120 0024 0027 0038 0048 0069 0069 K3 15xD 03xD 1xD 01xD 56 120 0024 0027 0038 0048 0069 0069 Cutting data for mills 015 585 Cutting speed m/min m/min ap ae 12 16 20 25 P0 15xD 003xD 215 0065 0075 01 01 P1 15xD 003xD 175 0065 0075 01 01 P2 15xD 003xD 175 0065 0075 01 01 P3 15xD 003xD 135 0065 0075 01 01 P4 15xD 003xD 95 0065 0075 01 01 P5 15xD 003xD 155 0065 0075 01 01 P6 15xD 003xD 115 0065 0075 01 01 P7 15xD 003xD 85 0065 0075 01 01 M1 15xD 003xD 115 0065 0075 01 01 K1 15xD 003xD 195 0065 0075 01 01 K2 15xD 003xD 165 0065 0075 01 01 K3 15xD 003xD 165 0065 0075 01 01 N3 15xD 003xD 155 0065 0075 01 01 N4 15xD 003xD 195 0065 0075 01 01 180 NORGAU Cutting data for mills Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group.