Feed per tooth is for slot milling For side milling increase Fz by 20% 1 m Cutting speed m/min Feed rate mm tooth ap ap 10 12 16 20 25 N1 1xD 05xD 1xD 212 300 0017 001

Feed per tooth is for slot milling For side milling increase Fz by 20% 1 m Cutting speed m/min Feed rate mm tooth ap ap 10 12 16 20 25 N1 1xD 05xD 1xD 212 300 0017 0017 0021 0042 0067 0067 0084 0101 0109 N2 1xD 05xD 1xD 176 250 0017 0017 0021 0042 0067 0067 0084 0101 0109 N3 1xD 05xD 1xD 141 200 0017 0017 0021 0042 0067 0067 0084 0101 0109 N4 1xD 05xD 1xD 113 160 0013 0013 0017 0025 0034 0034 0046 0059 0067 3 4 6 8 ae Cutting data for mills 015 675 Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group. Feed per tooth is for slot milling For side milling increase Fz by 20% Cutting speed m/min Feed rate k 1 mm tooth ap ae ap ae min max 3 4 5 6 8 10 12 14 16 20 P0 05xD 1xD 003xD 03xD 75 570 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 P1 05xD 1xD 003xD 03xD 60 450 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 P2 05xD 1xD 003xD 03xD 51 390 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 P3 05xD 1xD 003xD 03xD 48 360 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 P4 05xD 1xD 003xD 03xD 33 250 0003 0009 0009 0012 0015 0016 0016 0022 0022 0029 P5 05xD 1xD 003xD 03xD 46 350 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 P6 05xD 1xD 003xD 03xD 40 300 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 P7 05xD 1xD 003xD 03xD 26 200 0003 0009 0009 0012 0015 0016 0016 0022 0022 0029 P8 05xD 1xD 003xD 03xD 22 170 0003 0009 0009 0012 0015 0016 0016 0022 0022 0029 M1 05xD 1xD 003xD 03xD 29 220 0003 0009 0009 0012 0015 0016 0016 0022 0022 0029 K1 05xD 1xD 003xD 03xD 72 550 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 K2 05xD 1xD 003xD 03xD 66 500 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 K3 05xD 1xD 003xD 03xD 66 500 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 N4 05xD 1xD 003xD 03xD 92 700 0004 0013 0013 0016 002 0024 0024 0033 0033 0044 H1 05xD 1xD 003xD 03xD 17 130 0003 0009 0009 0012 0015 0016 0016 0022 0022 0029 NORGAU 175 Cutting tools Cutting data for mills 015 651 Lower value of cutting speed is used for high stock removal applications or for higher hardness (machinability) within group. Higher value of cutting speed is used for finishing applications or for lower hardness (machinability) within group.