TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS _ m/ix-nem/ Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Pre-hardened steel, Cartoon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steel, Titanium alloys AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Dil. DCfmmJ Cutting speed (minin) Nan Spindia Revolution (miir1) Food per Tooth (mm/tooth Table Fad (nun/min) Depth of cut ap(mm Hof cut hH Cutting feed (m/min) Mail Spndle Revdution (mar' Food por Tooth (mmltooth TaUe Feed tynmjmin) Depth dot ipH Width it cut Cutting speed minin) Main Sphde Revdution (miir1) Fasd per Tooth mnM TaUe Feed (mmtnin Depth of cut h of cut 10 12 16 20 25 200 200 200 200 200 6400 5300 4000 3200 2500 0.07 0.085 0.07 0.08 0.08 2700 2700 2800 3100 2400 10 12 16 20 25 1 1.2 0.64 0.8 1 150 150 150 150 150 4800 4000 3000 2400 1900 0.07 0.085 0.088 0.1 0.1 2000 2000 2600 2900 2300 10 12 16 20 25 1 1.2 0.64 0.8 1 100 100 100 100 100 3200 2700 2000 1600 1300 0.07 0.085 0.07 0.08 0.08 1300 1400 1400 1500 1200 10 12 16 20 25 1 1.2 0.64 0.8 1 ae Work material Heat resistant alloys lnconel718 Dh. Cling feed Miii Spindle Revdution Feed per Tooth Table Feed Depth of cut Hof cut DC(mm) (m/min) (miir1) (miriloothj (mm/min) ipH n(mm) 10 40 1300 0.033 260 10 0.5 12 40 1100 0.035 230 12 0.6 16 40 800 0.038 300 16 0.64 20 40 640 0.04 310 20 0.8 25 40 510 0.04 240 25 1 ae If the machining radius at the comer is the same as the tool radius when using the head with more than 10 flutes, please set the depth of cut and feed rate to half of the above. For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. If the depth of cut is shallow, the revolution and feed rate can be increased. The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. 1262 Mitsubishi Materials