TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS _ IMX-C4F0-C Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Cartoon steel, Alloy steel, Mild Steel, Copper, Copper alloys AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Hardened steel, Precipitation hardening stainless steel, Ferritic and Martensitic stainless steel AISI H13, AISI L6, AISI 431, AISI 420, AISI 630, AISI631 Oil. DCjmm) Cutting speed (minin Revolution (niir'l Feed per Toolh (mmltoolh TibleFeed (mm/min Depth of cut (mm) Width of cvt i (mm Cling feed (minin Revolution (mir1 Feed pei Toolh timltooth TaUe Feed (mmlmin) Depth if cut (mm Width if cut ilium Cutting speed minin Revolution Jniir1) Feed per Tooth mmM TaUe Feed (mmMn Depth of cut (mm Width if cut aeflnm 10 150 4800 0.4 7700 0.5 6 135 4300 0.4 6900 0.5 6 120 3800 0.3 4600 0.5 6 12 150 4000 0.45 7200 0.6 7.2 135 3600 0.45 6500 0.6 7.2 120 3200 0.3 3800 0.6 7.2 16 150 3000 0.5 6000 0.8 9.6 135 2700 0.5 5400 0.8 9.6 120 2400 0.4 3800 0.8 9.6 20 150 2400 0.5 4800 1 12 135 2100 0.5 4200 1 12 120 1900 0.4 3000 1 12 25 150 1900 0.5 3800 1.25 15 135 1700 0.5 3400 1.25 15 120 1500 0.4 2400 1.25 15 ae Work material Austenitic stainless steel, Titanium alloy, Cobalt chromium alloy AISI 304, AISI 316, AISI 304LN, AISI 316LN, Ti-6AI-4V Heat resistant alloys lnconel718 Dia. Cling speed Revolution Feed per Toolh Table Feed Depth of nt Width of cut Cutting speed Revdution Feed per Tooth TahleFeed Depth of cut Width of cut DCJnm )n/min) (niir'l mnMi mm/min) (mm ae(mm) (m/min (miir' mm/todti mm/min mm ae(imi 10 40 1300 0.2 1000 0.5 6 25 800 0.1 320 0.5 6 12 40 1100 0.2 880 0.6 7.2 25 660 0.1 260 0.6 7.2 16 40 800 0.3 960 0.8 9.6 25 500 0.15 300 0.8 9.6 20 40 640 0.3 770 1 12 25 400 0.15 240 1 12 25 40 510 0.3 610 1.25 15 25 320 0.15 190 1.25 15 ae For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. If the depth of cut is shallow, the revolution and feed rate can be increased. Vibration may occur if the rigidity of machine or work piece is low. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. Reduce the feed by 1/2 for ramping process. 1264 Mitsubishi Materials