TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS _ IMX-R4F Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Cartoon steel, Alloy steel, Mild Steel, Copper, Copper alloys AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steel, Titanium alloys AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V Dil. DCH Cutting speed (minin Revolution (niir1 Feed per Tooth (mm/tooth Table Feed (mm/min Depth of cut (ran Hof cut ae)nm Mug feed (m/min Revdution (mir') Feed per Tooth timltooth TaUe Feed (mmlmin) Depth if cut M Width if cut ao)nm Cutting apeed minin) Revolution Jniir1 Feed per Tooth mmM Table Feed (mmMn Depth of cut (mm Mh if cut 10 150 4800 0.045 860 8 4 120 3800 0.03 460 8 4 100 3200 0.038 480 8 4 12 150 4000 0.045 720 9.6 4.8 120 3200 0.033 420 9.6 4.8 100 2700 0.04 430 9.6 4.8 16 150 3000 0.05 600 12.8 6.4 120 2400 0.038 360 12.8 6.4 100 2000 0.045 360 12.8 6.4 20 150 2400 0.05 480 16 8 120 1900 0.038 290 16 8 100 1600 0.045 290 16 8 25 150 1900 0.06 460 20 10 120 1500 0.038 230 20 10 100 1300 0.045 230 20 10 ae Work material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Heat resistant alloys lnconel718 Dia. Cling epeed Revolution Feed per Teeth Table Feed Depth of nt Width of cut Cutting epeed Revotution Feed per Teeth Table Feed Depth of cut Whtthofcut DC)nm (m/min (liir1 mmM) mmlmin (mm ae(mm) (ir/min (miir1 mmltooth imMn mm n(nm) 10 75 2400 0.030 290 8 4 40 1300 0.04 210 8 1 12 75 2000 0.033 260 9.6 4.8 40 1100 0.045 200 9.6 1.2 16 75 1500 0.04 230 12.8 6.4 40 800 0.050 160 12.8 1.6 20 75 1200 0.04 180 16 8 40 640 0.050 130 16 2 25 75 950 0.04 140 20 10 40 510 0.050 100 20 3 For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. If the depth of cut is shallow, the revolution and feed rate can be increased. Vibration may occur if the rigidity of machine or work piece is low. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. Slotting Work material Carbon steel, Alloy steel, Mild Steel, Copper, Copper alloys AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steel, Titanium alloys AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V Dia. Cutting epeed Revolution Feed per M Table Feed Depth if cut Cling speed Revolution Feed per Tooth Table Feed Depth of cut Cutting apeed Revdim Feed per Teeth Table Feed Depth of cut DC(mm (mtnin) miir1 (mmltooth (mmlmin mm (mhiin) (mirr1 (mmlteoth (mmlmin) (mm mimin miir4 nmM mmlmin (mm 10 100 3200 0.04 510 5 80 2500 0.03 300 5 60 1900 0.02 150 4 12 100 2700 0.045 490 6 80 2100 0.032 270 6 60 1600 0.025 160 5 16 100 2000 0.05 400 8 80 1600 0.038 240 8 60 1200 0.03 140 6 20 100 1600 0.05 320 10 80 1300 0.038 200 10 60 950 0.034 130 8 25 100 1300 0.06 310 12 80 1000 0.038 150 12 60 760 0.034 100 10 1238 Mitsubishi Materials