Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS _ IMX-CH3L Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Chamfering (Hole circumference) Carbon steel, Alloy steel, Gray Cast Iron AIS11045, AISI 4140, ASTM A36, AIS11010 Work material Alloy tool steel, Carbon steel, Alloy steel, Pre-hardened steel SKD, SKT, AISI 4340, AISI P21, PX5 Austenitic stainless steel, Titanium alloy AISI 304, AISI 306, Ti-6AI-4V Dil. DCH No. of Flutes Cuttiig speed minin) Revolution niir1) Feed per Tooth tnmlt Feed nte (mm/min) Depth of cut ipH Depth of cut Cutting speed minh) (miir1) Feed per Tooth (nmll Feed rate (mm/niin Depth if cut Depth of cut Cutting speed (minin) (nr1 Feed per Tooth Feed nte (mmfmin) Depth of cut ap(rrm Depth of cut leflnm) 10 12 16 20 40 40 40 40 1300 1100 800 640 0.04 0.04 0.04 0.04 160 130 96 77 1.8 2.2 2.4 2.6 1.8 2.2 2.4 2.6 40 40 40 40 1300 1100 800 640 0.03 0.03 0.03 0.03 120 99 72 58 1.8 2.2 2.4 2.6 1.8 2.2 2.4 2.6 30 30 30 30 950 800 600 480 0.03 0.03 0.03 0.03 86 72 54 43 1.8 2.2 2.4 2.6 1.8 2.2 2.4 2.6 ap Work material Hardened steel (45 55HRC) AISI H13, AISI L6 Heat resistant alloys lnconel718 Dil. Cutting speed Mution FeedpuM Feed nte Depth cf cut Depth if cut Cutting speed Revolutitii Feed per Tooth Feed nte Depth of cut Depth of cut DCJnm) (minin (miir1) (mmA.) (mmfmin) apfn) eo nin) (m/min) (miir1) tnmlL (mmlmin) i"l ie(nin) 10 3 30 950 0.02 57 1.8 1.8 30 950 0.04 110 1.8 1.8 12 3 30 800 0.02 48 2.2 2.2 30 800 0.04 96 2.2 2.2 16 3 30 600 0.02 36 2.4 2.4 30 600 0.04 72 2.4 2.4 20 3 30 480 0.02 29 2.6 2.6 30 480 0.04 58 2.6 2.6 ap For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. Vibration may occur if the rigidity of machine or work piece is low. In this case, please reduce the revolution and feed rate proportionately. Chamfering (Shape circumference) Work material Carbon steel, Alloy steel, Gray Cast Iron AIS11045, AISI 4140, ASTM A36, AIS11010 Alloy tool steel, Carbon steel, Alloy steel, Pre-hardened steel SKD, SKT, AISI 4340, AISI P21, PX5 Austenitic stainless steel, Titanium alloy AISI 304, AISI 306, Ti-6AI-4V Dil. DCJnm) Ni of Flutes Cutting speed (nih Revolution (triir1) Feed per Tooth timlL Feed nte (mmMn Depth of cut eptnm) Cutting speed (minin) Revolution fitiir1) Feed per Tooth Feed nte (mmfrin) Depth of cut ipH Cutting speed (minin) Revolution miir4) Feed per Tooth mm/t) Feed nte (nrnlmrl Depth if cut eptnn) 10 3 100 3200 0.04 480 2.0 70 2200 0.03 300 2.0 60 1900 0.03 230 2.0 12 3 100 2700 0.04 410 2.4 70 1900 0.03 260 2.4 60 1600 0.03 190 2.4 16 3 100 2000 0.04 300 2.7 70 1400 0.03 190 2.7 60 1200 0.03 140 2.7 20 3 100 1600 0.04 240 3.2 70 1100 0.03 150 3.2 60 950 0.03 110 3.2 Mitsubishi Materials 1275 TAPER RADIUS BALL SQUARE carbide